Fråga  |
Svar |
What is the Protocol Data Unit (PDU) at Layer 1 of the OSI model? börja lära sig
|
|
|
|
|
Which of the following transmission media belong to the category of guided media? börja lära sig
|
|
Twisted pair, coaxial cable, and fiber optic
|
|
|
Why is differential signaling used in Ethernet? börja lära sig
|
|
To cancel external electromagnetic interference by subtracting the two opposing signals at the receiver
|
|
|
Which duplex mode is described by the classic walkie-talkie principle? börja lära sig
|
|
|
|
|
What is the main problem with NRZ-L (Non-Return-to-Zero Level) encoding when transmitting long runs of identical bits? börja lära sig
|
|
Long runs of the same bit produce no signal transitions, causing the receiver to lose clock synchronization
|
|
|
Which encoding scheme does 100BASE-TX use, and what efficiency does it achieve? börja lära sig
|
|
4B/5B with MLT-3, 80% efficiency
|
|
|
How many discrete voltage levels does PAM-5 use, as employed in 1000BASE-T (Gigabit Ethernet)? börja lära sig
|
|
5 levels (−2, −1, 0, +1, +2)
|
|
|
What does the abbreviation BASE mean in Ethernet designations such as 10BASE-T? börja lära sig
|
|
Baseband transmission — the entire cable carries a single digital signal
|
|
|
A noise-free channel has a bandwidth of 5 MHz and uses PAM-4 (4 signal levels). What is the maximum data rate according to the Nyquist theorem? börja lära sig
|
|
|
|
|
What does the Shannon-Hartley theorem describe? börja lära sig
|
|
The absolute theoretical upper limit of the data rate on a noisy channel, regardless of the encoding scheme used
|
|
|
What is the maximum supported data rate of Cat5e cables? börja lära sig
|
|
|
|
|
What is the maximum reach of Cat6 at 10 Gbit/s, and why is Cat6A superior? börja lära sig
|
|
Cat6 only reaches 55 m at 10G; Cat6A achieves
|
|
|
How much power does the PoE standard IEEE 802.3at (PoE+) deliver to the powered device (PD)? börja lära sig
|
|
|
|
|
IEEE 802.3bt Type 4 delivers up to 71.3 W. Which cable category is recommended for long PoE runs, and why? börja lära sig
|
|
Cat6A or cables with larger conductor cross-sections, to minimize resistive losses over long distances
|
|
|
Why can PoE (Power over Ethernet) not be transmitted over fiber optic cables? börja lära sig
|
|
Fiber is an electrical insulator (glass) and cannot conduct electric current
|
|
|
What is the core diameter of single-mode fiber (SMF), and what does this enable? börja lära sig
|
|
8–9 µm, allowing only one light mode and enabling distances of 80 km or more
|
|
|
Why must APC connectors (8° angled) never be mated with UPC connectors (flat-polished)? börja lära sig
|
|
The angular mismatch creates an air gap that physically damages both ferrules and causes high insertion loss
|
|
|
A new 10 Gbit/s copper run of 80 m is planned (no EMI, limited budget). Which cable category is correct? börja lära sig
|
|
Cat6A — supports 10GBASE-T up to
|
|
|
What is the maximum allowed untwist length when terminating Cat6A cables at an RJ45 connector? börja lära sig
|
|
|
|
|
In NRZI (Non-Return-to-Zero Inverted) encoding, how is a binary 1 represented on the wire? börja lära sig
|
|
A transition (level change) occurs at the start of the bit period
|
|
|
What signaling scheme does 100BASE-TX place on the wire after 4B/5B block coding? börja lära sig
|
|
MLT-3 (Multi-Level Transmit, three levels)
|
|
|
Why does 4B/5B coding map 4 data bits onto 5-bit code words? börja lära sig
|
|
The redundant codes guarantee enough transitions (no more than three consecutive zeros) for clock recovery
|
|
|
What is the main purpose of scrambling a bit stream before transmission? börja lära sig
|
|
To randomize the data so long runs of identical bits are broken up, aiding clock recovery and reducing spectral peaks
|
|
|
Differential Manchester encoding signals a binary 0 by börja lära sig
|
|
a transition at the start of the bit period (the mandatory mid-bit transition is always present)
|
|
|
Why does MLT-3 reduce the dominant signal frequency compared to binary NRZI at the same bit rate? börja lära sig
|
|
It takes four bit periods to complete one full waveform cycle, so the fundamental frequency is about one quarter of the bit rate
|
|
|
Which Ethernet standard uses Manchester encoding on the wire? börja lära sig
|
|
|
|
|
A channel has a bandwidth of 4 kHz and uses 4 signal levels. What is the Nyquist capacity? C = 2 · B · log2(L). börja lära sig
|
|
|
|
|
Using the Nyquist formula C = 2 · B · log2(L), how many signal levels are required to reach 24 kbit/s over a 3 kHz channel? börja lära sig
|
|
|
|
|
A channel has B = 1 MHz and a linear SNR of 3. What is the approximate Shannon capacity? C = B · log2(1 + SNR). börja lära sig
|
|
|
|
|
A 10 MHz channel has an SNR of 20 dB. What is the approximate Shannon capacity? (20 dB = linear 100.) börja lära sig
|
|
|
|
|
Bandwidth and data rate are related but distinct. Which statement is correct? börja lära sig
|
|
Bandwidth is a frequency range in Hz; for a fixed bandwidth the data rate rises by using more signal levels or higher SNR
|
|
|
A −10 dB change in power corresponds to which multiplier? börja lära sig
|
|
|
|
|
What does 0 dBm represent in absolute terms? börja lära sig
|
|
|
|
|
Differential signaling cancels external noise because börja lära sig
|
|
the same interference is induced on both wires and the receiver outputs the difference (A − B), removing the common component
|
|
|
Which duplex mode transmits in one direction only, such as a broadcast TV signal? börja lära sig
|
|
|
|
|
Cat6 cable is specified to what frequency bandwidth? börja lära sig
|
|
|
|
|
Cat8 cable is specified to which bandwidth, and what is its maximum reach? börja lära sig
|
|
2,000 MHz, with a maximum reach of about 30 m
|
|
|
A standard twisted-pair data cable contains how many pairs, and why are the pairs twisted at different rates? börja lära sig
|
|
Four pairs; different twist rates reduce crosstalk between the pairs
|
|
|
Why must shielded cabling be properly grounded at the appropriate point(s)? börja lära sig
|
|
Improper grounding can let the shield act as an antenna and worsen performance instead of improving it
|
|
|
FEXT (Far-End Crosstalk) is distinguished from NEXT by börja lära sig
|
|
being measured at the far end of the link, where the disturbing signal has also attenuated
|
|
|
Why is alien crosstalk the key barrier that Cat6A addresses for 10GBASE-T over 100 m? börja lära sig
|
|
Because 10 Gbit/s uses all pairs in both directions, and AXT from neighboring cables cannot be cancelled by the receiver; Cat6A's design and shielding suppress it
|
|
|
What limits the distance and bandwidth of multimode fiber compared to single-mode? börja lära sig
|
|
Modal dispersion, as different light paths (modes) arrive at slightly different times
|
|
|
Which fiber wavelength is associated with the C-band used for long-haul single-mode transmission and lowest attenuation? börja lära sig
|
|
|
|
|
The ST fiber connector is characterized by which coupling mechanism? börja lära sig
|
|
|
|
|
By color code, an APC connector body is typically which color, and UPC which color? börja lära sig
|
|
APC is green; UPC is blue
|
|
|
IEEE 802.3bt Type 4 (PoE++) delivers what power at the PSE, and what is available at the powered device? börja lära sig
|
|
Up to 90 W at the PSE, with about 71.3 W available at the PD
|
|
|
What does the "BASE" in standards like 100BASE-TX and 1000BASE-T denote? börja lära sig
|
|
Baseband signaling, where the medium carries a single digital signal occupying the full bandwidth
|
|
|
How many pairs does 1000BASE-T use, and in what manner? börja lära sig
|
|
All 4 pairs, each carrying data bidirectionally and simultaneously with echo cancellation
|
|
|
What is the baud (symbol) rate of 100BASE-TX on the wire? börja lära sig
|
|
|
|
|
Which Ethernet copper standard requires Cat6A to reliably reach 100 m? börja lära sig
|
|
|
|
|
What is the chief disadvantage of Manchester encoding that motivated its replacement at 100 Mbit/s? börja lära sig
|
|
It needs twice the bandwidth of the bit rate (only 50 percent efficient)
|
|
|
Which statement about clock recovery and line coding is correct? börja lära sig
|
|
A good line code guarantees frequent transitions so the receiver can continuously recover and lock its clock to the data
|
|
|
What is the Protocol Data Unit (PDU) at Layer 2 of the OSI model? börja lära sig
|
|
|
|
|
What is the main function of the LLC sublayer (Logical Link Control, IEEE 802.2)? börja lära sig
|
|
Protocol multiplexing: identifying the Layer 3 protocol (IP, ARP, IPv6) carried in the frame
|
|
|
What do the first 3 bytes (24 bits) of a MAC address encode? börja lära sig
|
|
The OUI (Organizationally Unique Identifier) — the manufacturer identifier assigned by the IEEE
|
|
|
What does I/G bit = 1 in the first byte of a MAC address indicate? börja lära sig
|
|
The address is a multicast or broadcast address (group address)
|
|
|
Which MAC address is the universal broadcast address, and which protocols typically use it? börja lära sig
|
|
FF: FF: FF: FF: FF: FF — used by ARP requests and DHCP Discover, among others
|
|
|
An Ethernet frame contains EtherType 0x0806. Which Layer 3 protocol is in the payload? börja lära sig
|
|
ARP (Address Resolution Protocol)
|
|
|
Why is the minimum Ethernet frame size 64 bytes? börja lära sig
|
|
Due to the legacy CSMA/CD mechanism: a frame had to be long enough so that it was still being transmitted when the collision signal returned from the far end of the cable
|
|
|
What does the MTU (Maximum Transmission Unit) define in standard Ethernet, and how does it differ from the total frame size? börja lära sig
|
|
The MTU is 1500 bytes (payload only); the total frame size is up to 1518 bytes (Preamble/SFD are outside the counted frame)
|
|
|
What can CRC-32 (Frame Check Sequence) do, and what can it NOT do? börja lära sig
|
|
CRC-32 can detect errors but NOT correct them; corrupted frames are silently discarded, and correction is handled by higher-layer protocols such as TCP
|
|
|
What is the function of the preamble (7 bytes) in an Ethernet frame? börja lära sig
|
|
It is an alternating 1-0 pattern that allows the receiver to synchronize its clock to the incoming signal frequency before the actual data arrives
|
|
|
What is the fundamental difference between a hub (Layer 1) and a switch (Layer 2) regarding collision domains? börja lära sig
|
|
A hub forms one large shared collision domain for all ports; a switch creates a separate collision domain per port (full-duplex, no collisions)
|
|
|
What does a switch do when it receives a frame destined for a MAC address that is not in its CAM table? börja lära sig
|
|
It floods the frame to all ports except the ingress port (unknown unicast flooding)
|
|
|
Why can devices in different VLANs not communicate directly at Layer 2? börja lära sig
|
|
VLANs create separate broadcast domains; a Layer 3 device (router or L3 switch) is required for inter-VLAN communication
|
|
|
Which EtherType value does an 802.1Q VLAN tag use in an Ethernet frame? börja lära sig
|
|
|
|
|
How long does convergence take in classic STP (802.1D), and what is the operational consequence? börja lära sig
|
|
Approximately 30–50 seconds; this represents a significant outage during topology changes
|
|
|
Host A (192.168.1.10) wants to send a frame to Host B (192.168.1.20) but does not know its MAC address. Which ARP sequence is correct? börja lära sig
|
|
Host A broadcasts an ARP Request to FF: FF: FF: FF: FF: FF; only Host B replies with a unicast ARP Reply containing its MAC address; Host A caches the mapping in its ARP table
|
|
|
What is a Gratuitous ARP, and for which legitimate purposes is it used? börja lära sig
|
|
An unsolicited ARP Reply in which a device announces its own IP-to-MAC mapping; used at boot time, during failover, and to detect IP address conflicts
|
|
|
Which of the four core functions of the Data Link Layer is responsible for organizing a raw stream of bits into structured units before transmission? börja lära sig
|
|
|
|
|
How many total bits and bytes make up a standard MAC address? börja lära sig
|
|
|
|
|
When the I/G bit (bit 0 of the first byte) of a MAC address is 0, the address is: börja lära sig
|
|
A unicast address (a single, individual device)
|
|
|
The Logical Link Control (LLC) sublayer is defined by which IEEE standard? börja lära sig
|
|
|
|
|
In an Ethernet II frame, how large is the EtherType field? börja lära sig
|
|
|
|
|
What is the valid payload size range of a standard Ethernet II frame? börja lära sig
|
|
|
|
|
An end station receives an Ethernet frame with EtherType 0x0800. Which protocol does the payload contain? börja lära sig
|
|
|
|
|
How large is the Preamble in an Ethernet frame, and what is its purpose? börja lära sig
|
|
7 bytes of alternating 1-0 pattern used for receiver clock synchronization
|
|
|
What is the standard Ethernet MTU, and what does it count? börja lära sig
|
|
1500 bytes, counting the payload only
|
|
|
A station needs to send a payload of only 20 bytes. What happens to satisfy the minimum frame size? börja lära sig
|
|
The payload is padded up to 46 bytes so the total frame reaches 64 bytes
|
|
|
Which of the following is NOT something CRC-32 can detect? börja lära sig
|
|
It cannot correct any errors it finds
|
|
|
What is the typical default aging timer for entries in a switch CAM table? börja lära sig
|
|
|
|
|
In a CAM table overflow attack, the attacker floods the switch with many random source MAC addresses. What is the result? börja lära sig
|
|
The CAM table fills up and the switch falls back to flooding all frames, allowing the attacker to sniff traffic
|
|
|
At which OSI layer does a hub operate, and how does it handle an incoming frame? börja lära sig
|
|
Layer 1; it repeats the signal out of all other ports regardless of destination
|
|
|
A bridge and a switch are functionally related. Which statement best describes their relationship? börja lära sig
|
|
A switch is essentially a multiport bridge implemented in hardware; both operate at Layer 2 and learn MAC addresses
|
|
|
The 64-byte minimum Ethernet frame size is fundamentally tied to which mechanism? börja lära sig
|
|
CSMA/CD collision detection — the frame must still be transmitting when a collision signal could return from the far end
|
|
|
In an 802.1Q tag, what is the value of the TPID field that identifies the frame as VLAN-tagged? börja lära sig
|
|
|
|
|
What is the function of the 3-bit PCP (Priority Code Point) field in an 802.1Q tag? börja lära sig
|
|
It carries a Class of Service (CoS) priority value from 0 to 7 for QoS
|
|
|
On a trunk port, frames belonging to the native VLAN are transmitted in what manner? börja lära sig
|
|
|
|
|
Two PCs are connected to the same switch but are in VLAN 10 and VLAN 20 respectively. To communicate, what is required? börja lära sig
|
|
A Layer 3 device (router or L3 switch) with an interface in each VLAN
|
|
|
Classic STP is defined by which IEEE standard? börja lära sig
|
|
|
|
|
How does STP elect the root bridge? börja lära sig
|
|
The switch with the lowest Bridge ID becomes the root bridge
|
|
|
Which destination MAC address is used for STP BPDU (Bridge Protocol Data Unit) frames? börja lära sig
|
|
|
|
|
What is the role of an STP root port on a non-root switch? börja lära sig
|
|
It is the port with the lowest path cost toward the root bridge
|
|
|
In which STP port state does a port populate the MAC address table but still not forward user frames? börja lära sig
|
|
|
|
|
Which standard STP path cost corresponds to a 100 Mbps link? börja lära sig
|
|
|
|
|
How does the target host send its ARP Reply? börja lära sig
|
|
As a unicast directly back to the requesting host
|
|
|
What is the typical default timeout for entries in a host's ARP cache? börja lära sig
|
|
|
|
|
A user on an access port in VLAN 10 cannot reach a server on the same switch. show vlan brief reveals the server's port is in VLAN 20. What is the cause? börja lära sig
|
|
A VLAN mismatch — the two devices are in different broadcast domains and need Layer 3 routing
|
|
|
Two directly connected switch ports show many late collisions and CRC errors, and throughput is poor. show interfaces status hints at a configuration issue. What is the most likely cause? börja lära sig
|
|
A duplex mismatch (one side half-duplex, the other full-duplex)
|
|
|
Cut-through switching achieves very low latency because it: börja lära sig
|
|
Begins forwarding as soon as the destination MAC is read, without waiting for the full frame or CRC check
|
|
|
Which Layer 2 attack is mitigated by Dynamic ARP Inspection (DAI)? börja lära sig
|
|
ARP spoofing (ARP cache poisoning)
|
|
|
Wireshark display filter eth. type == 0x0806 would capture which traffic? börja lära sig
|
|
|
|
|
Link Aggregation (IEEE 802.3ad / LACP) combines multiple physical links. How does it typically distribute traffic? börja lära sig
|
|
By hashing fields such as source/destination MAC or IP to select a member link (per-flow)
|
|
|
The destination MAC FF: FF: FF: FF: FF: FF in a frame tells a switch to: börja lära sig
|
|
Flood the frame to all ports except the ingress port
|
|
|
An IPv4 address is structured as 32 bits. How are these bits grouped in dotted-decimal notation? börja lära sig
|
|
Four octets of 8 bits each, separated by dots
|
|
|
What is the decimal value of the binary octet 00010000? börja lära sig
|
|
|
|
|
Which 8-bit binary value represents the decimal number 172? börja lära sig
|
|
|
|
|
How many total IPv4 addresses are theoretically possible with 32 bits? börja lära sig
|
|
|
|
|
Which IPv4 address class is reserved for multicast? börja lära sig
|
|
|
|
|
Which CIDR prefix corresponds to the RFC 1918 private range 172.16.0.0? börja lära sig
|
|
|
|
|
What is the full address range covered by the loopback block 127.0.0.0/8? börja lära sig
|
|
|
|
|
The address block 169.254.0.0/16 is used for which purpose? börja lära sig
|
|
Link-Local / APIPA addresses self-assigned when DHCP fails
|
|
|
How many usable host addresses does a /29 subnet provide? börja lära sig
|
|
|
|
|
How many /28 subnets can be created from a single /24 network? börja lära sig
|
|
|
|
|
What is the dotted-decimal subnet mask for a /20 prefix? börja lära sig
|
|
|
|
|
What is the network address of host 10.10.10.130 with a /25 mask? börja lära sig
|
|
|
|
|
For the subnet 192.168.1.64/26, what are the first and last usable host addresses? börja lära sig
|
|
First: 192.168.1.65, Last: 192.168.1.126
|
|
|
Using a /27 mask, what is the block size (number of addresses per subnet)? börja lära sig
|
|
|
|
|
A point-to-point WAN link needs only 2 usable addresses. Which prefix is the classic choice? börja lära sig
|
|
|
|
|
In a VLSM design, after allocating Engineering 10.0.0.0/25 (126 hosts), at which address does the next subnet start? börja lära sig
|
|
|
|
|
The IHL (Internet Header Length) field holds its minimum value of 5. How many bytes of header does this represent? börja lära sig
|
|
20 bytes (5 × 4-byte words)
|
|
|
What is the purpose of the Identification field in the IPv4 header? börja lära sig
|
|
It carries the same value for all fragments of one original packet so the destination can group them for reassembly
|
|
|
Which protocol number appears in the IPv4 Protocol field for UDP? börja lära sig
|
|
|
|
|
The MF (More Fragments) flag is set to 0. What does this indicate? börja lära sig
|
|
This is the last fragment (or the packet was not fragmented)
|
|
|
What is the principle behind Path MTU Discovery using the DF flag? börja lära sig
|
|
Send packets with DF set; if a router cannot forward without fragmenting it returns an ICMP "fragmentation needed" message, so the sender lowers packet size
|
|
|
What is the correct name for the PDU (Protocol Data Unit) at Layer 3 of the OSI model? börja lära sig
|
|
|
|
|
Why are both MAC addresses (Layer 2) and IP addresses (Layer 3) necessary? börja lära sig
|
|
MAC addresses are flat and non-hierarchical (routing is not possible); IP addresses are hierarchical and enable routing.
|
|
|
How many bits does an IPv4 address consist of, and how many possible addresses does that theoretically yield? börja lära sig
|
|
32 bits, approximately 4.3 billion addresses (2^32)
|
|
|
What is the decimal value of the binary number 10101100? börja lära sig
|
|
|
|
|
A host has the IP address 192.168.1.100 with a /24 subnet mask. What is the network portion and what is the host portion? börja lära sig
|
|
Network: 192.168.1, Host:
|
|
|
What is the purpose of the 169.254.x. x (APIPA / Link-Local) address range? börja lära sig
|
|
It is automatically assigned when a device cannot reach a DHCP server.
|
|
|
Which organization manages IP address allocation in Europe (including Austria)? börja lära sig
|
|
|
|
|
What was the main advantage of introducing CIDR in 1993 over classful addressing? börja lära sig
|
|
CIDR allows flexible prefix lengths (e.g., /22) instead of being restricted to fixed Class A, B, or C sizes, dramatically reducing address waste.
|
|
|
Why are 2 addresses always subtracted from the total number of addresses in a subnet when calculating usable hosts? börja lära sig
|
|
Because the network address (all host bits = 0) and the broadcast address (all host bits = 1) cannot be assigned to any device.
|
|
|
What is the broadcast address of the subnet 192.168.1.64/26? börja lära sig
|
|
|
|
|
What is VLSM (Variable Length Subnet Masking) and why is it used in practice? börja lära sig
|
|
VLSM allows different prefix lengths within the same address space, so subnets can be sized precisely for their actual needs (e.g., /25 for
|
|
|
A company needs a subnet for exactly 500 hosts. What is the smallest prefix that meets this requirement? börja lära sig
|
|
|
|
|
How large is an IPv4 header without options, and what is the minimum value of the IHL field? börja lära sig
|
|
20 bytes; minimum IHL value = 5 (5 × 4 bytes = 20 bytes)
|
|
|
Where does the reassembly of fragmented IPv4 packets take place? börja lära sig
|
|
Exclusively at the destination host — never at intermediate routers.
|
|
|
What is the function of the default gateway for a host? börja lära sig
|
|
It is the IP address of the router interface on the local subnet; the host forwards all packets destined for other networks to this address.
|
|
|
A routing table contains the entries 10.0.0.0/8, 10.50.0.0/16, and 0.0.0.0/0. A packet arrives destined for 10.50.5.1. Which route is used? börja lära sig
|
|
10.50.0.0/16, because /16 is the longest matching prefix.
|
|
|
What happens at Layer 2 when a router receives a packet on interface eth0 and forwards it out interface eth1? börja lära sig
|
|
The router strips the old Layer 2 header (with the incoming MAC addresses), creates a new Layer 2 header with the appropriate MAC addresses for the next link, and decrements the TTL.
|
|
|
A user reports no internet connectivity. Running ipconfig / ip addr shows the IP address 169.254.15.23. What is the most likely cause? börja lära sig
|
|
The device failed to reach a DHCP server and automatically assigned itself an APIPA address (169.254.x.x).
|
|
|
How many bits does an IPv6 address use? börja lära sig
|
|
|
|
|
In which year was the global IANA IPv4 address pool fully depleted? börja lära sig
|
|
|
|
|
How many addresses does the IPv6 address space provide (approximately)? börja lära sig
|
|
|
|
|
What is the standard subnet prefix length for an IPv6 subnet? börja lära sig
|
|
|
|
|
IPv6 has no broadcast. What mechanism replaces broadcast functionality? börja lära sig
|
|
|
|
|
Which IPv6 address type is automatically generated on every interface, never routed beyond the local link, and starts with fe80:? börja lära sig
|
|
|
|
|
What is the prefix for IPv6 Global Unicast Addresses (GUA)? börja lära sig
|
|
|
|
|
What is the IPv6 loopback address? börja lära sig
|
|
|
|
|
The IPv6 header has a fixed size of how many bytes? börja lära sig
|
|
|
|
|
How many fields does the IPv6 header contain? börja lära sig
|
|
|
|
|
IPv6 does not include a header checksum. börja lära sig
|
|
|
|
|
In IPv6, routers can fragment packets if they are too large for a link. börja lära sig
|
|
|
|
|
The IPv6 "Hop Limit" field serves the same purpose as the IPv4 TTL field. börja lära sig
|
|
|
|
|
Expand the abbreviated IPv6 address 2001: db8:1 to its full form. Which is correct? börja lära sig
|
|
2001:0db8:0000:0000:0000:0000:0000:0001
|
|
|
Why may the: (double colon) appear only once in an IPv6 address? börja lära sig
|
|
Using it twice would make the number of replaced zero groups ambiguous
|
|
|
The IPv6 default route covering all destinations is expressed as: börja lära sig
|
|
|
|
|
In practice, which sub-range of the ULA block is actually used because the L bit is set to 1 for locally assigned prefixes? börja lära sig
|
|
|
|
|
Which prefix identifies all IPv6 multicast addresses? börja lära sig
|
|
|
|
|
The solicited-node multicast address used by Neighbor Discovery is formed from which prefix? börja lära sig
|
|
|
|
|
A GUA (Global Unicast) address typically divides into which three parts? börja lära sig
|
|
Global routing prefix, subnet ID, interface ID
|
|
|
Within a /48 site allocation, how many bits remain for the subnet ID before the /64 interface boundary? börja lära sig
|
|
|
|
|
When pinging a link-local address such as fe80:1, why must the interface (zone ID) be specified, e.g. fe80:1%eth0? börja lära sig
|
|
Link-local addresses are not unique across interfaces, so the host must know which link to use
|
|
|
Which of these addresses is a link-local address? börja lära sig
|
|
fe80: a1: b2ff: fe03: c4d5
|
|
|
Roughly how many addresses does the 128-bit IPv6 space contain? börja lära sig
|
|
|
|
|
Which IPv6 header field is used for QoS / DSCP marking, analogous to the IPv4 Type of Service? börja lära sig
|
|
|
|
|
Which IPv6 header field identifies the type of the next header (upper-layer protocol or extension header)? börja lära sig
|
|
|
|
|
In the IPv6 Next Header field, which value indicates that UDP follows? börja lära sig
|
|
|
|
|
Optional IPv6 functionality (fragmentation, source routing, IPsec) is carried in what? börja lära sig
|
|
Extension headers chained via the Next Header field
|
|
|
Which Next Header value identifies the Fragment extension header? börja lära sig
|
|
|
|
|
Because IPv6 routers never fragment, what must the source use to avoid oversized packets? börja lära sig
|
|
|
|
|
Which RFC defines stateless address autoconfiguration (SLAAC)? börja lära sig
|
|
|
|
|
During Duplicate Address Detection, what message does the host send and to which destination? börja lära sig
|
|
A Neighbor Solicitation to the solicited-node multicast address
|
|
|
After inserting FFFE, the EUI-64 process flips which bit of the first byte? börja lära sig
|
|
The 7th bit (the U/L, universal/local bit)
|
|
|
What privacy problem do Privacy Extensions (RFC 4941) solve? börja lära sig
|
|
EUI-64 embeds the MAC address, allowing devices to be tracked across networks
|
|
|
In stateless DHCPv6 (RA flags A=1, O=1), how is the address obtained versus the extra configuration? börja lära sig
|
|
The address comes from SLAAC; DHCPv6 supplies extra info such as DNS servers
|
|
|
On which UDP port does a DHCPv6 client listen? börja lära sig
|
|
|
|
|
Which RFC defines the Neighbor Discovery Protocol (NDP)? börja lära sig
|
|
|
|
|
Which ICMPv6 type number is assigned to the Neighbor Solicitation message? börja lära sig
|
|
|
|
|
Which NDP message lets a router inform a host of a better next-hop for a destination? börja lära sig
|
|
|
|
|
What does NAT64 accomplish? börja lära sig
|
|
It translates between IPv6 and IPv4 so IPv6-only clients can reach IPv4 servers
|
|
|
Which compressed address is INVALID because it uses: more than once? börja lära sig
|
|
|
|
|
Which everyday IPv6 functions rely on link-local addresses? börja lära sig
|
|
NDP, SLAAC router solicitation/advertisement, and routing-protocol adjacencies
|
|
|
IPv6 routers along the path are allowed to fragment packets that exceed the link MTU. börja lära sig
|
|
|
|
|
DHCPv6 servers listen on UDP port 546 while clients use 547. börja lära sig
|
|
|
|
|
IPv6 still includes a header checksum that routers recalculate at each hop. börja lära sig
|
|
|
|
|
The IPv6 loopback address: 1 is 64 bits long. börja lära sig
|
|
|
|
|
Neighbor Solicitation messages are sent to the solicited-node multicast address during address resolution and DAD. börja lära sig
|
|
|
|
|
When abbreviating an IPv6 address, the rule is that: (double colon) can be used to replace the longest consecutive run of all-zero groups. How many times can: appear in a single address? börja lära sig
|
|
|
|
|
In SLAAC, a host sends a Router Solicitation to which IPv6 multicast address? börja lära sig
|
|
|
|
|
DHCPv6 uses which UDP ports? börja lära sig
|
|
|
|
|
Privacy Extensions (RFC 4941) generate a random Interface ID to prevent börja lära sig
|
|
tracking of users across networks via their MAC-derived address
|
|
|
What is the difference between forwarding (data plane) and routing (control plane)? börja lära sig
|
|
Forwarding moves individual packets based on the routing table; routing builds and maintains the routing table using protocols
|
|
|
A routing table contains entries for 10.0.0.0/8, 10.1.0.0/16, and 10.1.1.0/24. A packet is destined for 10.1.1.50. Which entry will the router use? börja lära sig
|
|
10.1.1.0/24 (most specific match)
|
|
|
To enable IPv4 forwarding on a Linux system, which file must contain the value 1? börja lära sig
|
|
/proc/sys/net/ipv4/ip_forward
|
|
|
Static routes added with "ip route add" on Linux are lost after a reboot. börja lära sig
|
|
|
|
|
What is an Autonomous System (AS)? börja lära sig
|
|
A network or group of networks under one administrative authority with a unified routing policy
|
|
|
Which algorithm does OSPF use to calculate the shortest path? börja lära sig
|
|
Dijkstra SPF (Shortest Path First)
|
|
|
Which routing protocol uses the DUAL algorithm and supports unequal-cost load balancing? börja lära sig
|
|
|
|
|
BGP prevents routing loops by using the börja lära sig
|
|
AS-PATH attribute (a route that already contains the local AS is rejected)
|
|
|
PAT (Port Address Translation) allows many private IP addresses to share a single public IP address. What field is used to distinguish the individual connections? börja lära sig
|
|
|
|
|
CGNAT (Carrier-Grade NAT) uses which reserved address range? börja lära sig
|
|
|
|
|
In a firewall rule set, the principle that "what is not explicitly permitted is denied" is called: börja lära sig
|
|
|
|
|
Which plane of operation is responsible for moving an individual packet from an input interface to an output interface? börja lära sig
|
|
The data plane (forwarding)
|
|
|
A Linux route shows "proto kernel scope link src 192.168.1.10". What kind of route is this? börja lära sig
|
|
A directly connected route, auto-created when the IP address was assigned to the interface
|
|
|
A routing table has 192.168.0.0/16 and 192.168.4.0/24. A packet for 192.168.9.7 arrives. Which entry is used? börja lära sig
|
|
192.168.0.0/16, because 192.168.9.7 does not fall inside 192.168.4.0/24
|
|
|
Which is a genuine disadvantage of static routing? börja lära sig
|
|
It does not scale and provides no automatic failover when topology changes
|
|
|
By default, a Linux machine with two NICs in different subnets will NOT route packets between them because börja lära sig
|
|
IP forwarding is disabled by default and the packet is silently dropped
|
|
|
A router is a Layer 3 device that börja lära sig
|
|
connects different subnets and forwards packets between them based on IP addresses
|
|
|
Which categorisation is correct? börja lära sig
|
|
OSPF and IS-IS are link-state IGPs; RIP and EIGRP are distance-vector IGPs; BGP is a path-vector EGP
|
|
|
Which RIP loop-prevention technique stops a router from advertising a route back out the interface on which it was learned? börja lära sig
|
|
|
|
|
Which transport protocol and port does RIP use to exchange updates? börja lära sig
|
|
|
|
|
How does OSPF differ from RIP regarding update behaviour? börja lära sig
|
|
OSPF sends updates only when the topology changes, not periodically like RIP
|
|
|
An OSPF Area Border Router (ABR) börja lära sig
|
|
connects one or more non-backbone areas to the backbone Area 0
|
|
|
Which protocol uses a composite metric based primarily on bandwidth and delay and guarantees loop-free paths with DUAL? börja lära sig
|
|
|
|
|
Which statement about BGP route selection is most accurate? börja lära sig
|
|
BGP selects routes based on policy and business relationships, not strictly the shortest path
|
|
|
What is the Administrative Distance of iBGP? börja lära sig
|
|
|
|
|
Two routing sources advertise the same network: OSPF (AD 110) and EIGRP internal (AD 90). Which route is installed in the routing table? börja lära sig
|
|
The EIGRP route, because a lower Administrative Distance is more trusted
|
|
|
Which statement about Static NAT is correct? börja lära sig
|
|
It provides a permanent one-to-one mapping between a private and a public IP, allowing inbound access (e.g., to a server)
|
|
|
Approximately how many simultaneous sessions can a single public IP support under PAT, limited by the source-port field? börja lära sig
|
|
Around 65,000 (limited by the 16-bit port range)
|
|
|
A major drawback of NAT for certain applications is that it börja lära sig
|
|
breaks true end-to-end connectivity, complicating protocols like FTP, SIP/VoIP, and IPsec AH
|
|
|
What is a key consequence of an ISP deploying CGNAT? börja lära sig
|
|
It adds a second layer of NAT, so customers share public IPs and inbound connections become harder
|
|
|
Which conntrack state describes the very first packet of a new connection? börja lära sig
|
|
|
|
|
The default-deny (implicit deny) principle means börja lära sig
|
|
anything not explicitly permitted by a rule is dropped
|
|
|
In iptables, packets generated by the local host itself traverse which chain? börja lära sig
|
|
|
|
|
Which Linux firewalling framework is the modern successor to iptables, unifying IPv4, IPv6, ARP, and bridge filtering? börja lära sig
|
|
|
|
|
Traceroute reveals the path a packet takes by börja lära sig
|
|
sending packets with incrementing TTL values and collecting the ICMP Time Exceeded replies from each hop
|
|
|
In a TCP segment, what does the Acknowledgment Number field actually contain? börja lära sig
|
|
The sequence number of the NEXT byte the receiver expects to receive
|
|
|
What is the semantic difference between the PSH and URG flags in TCP? börja lära sig
|
|
PSH tells the receiver to deliver buffered data to the application immediately; URG marks a region of the stream (via the Urgent Pointer) as priority out-of-band data
|
|
|
What is the purpose of TCP keepalive probes? börja lära sig
|
|
To detect dead peers and keep idle-connection state alive by periodically probing a connection that has had no data for a long time
|
|
|
What problem does Karn's algorithm solve in TCP's RTT estimation? börja lära sig
|
|
It excludes RTT samples from retransmitted segments, removing the ambiguity of not knowing whether an ACK matches the original or the retransmission
|
|
|
Why is QUIC 0-RTT data considered vulnerable to replay attacks? börja lära sig
|
|
The early data is sent before the full handshake completes using a pre-shared key, so an attacker can capture and resend it; therefore only idempotent requests should be sent as 0-RTT
|
|
|
How many bits is a port number? börja lära sig
|
|
|
|
|
What is the port range for well-known (system) ports? börja lära sig
|
|
|
|
|
What is the port range for dynamic/ephemeral ports? börja lära sig
|
|
|
|
|
How many values are used to uniquely identify a TCP connection (the so-called 4-tuple)? börja lära sig
|
|
Source IP + source port + destination IP + destination port (4 values)
|
|
|
A web server can handle thousands of simultaneous TCP connections to the same port 443 because: börja lära sig
|
|
Each connection has a unique 4-tuple (different source IP and/or source port)
|
|
|
Which "ss" command shows all listening TCP and UDP ports with their owning process? börja lära sig
|
|
|
|
|
Which well-known port does SSH use? börja lära sig
|
|
|
|
|
Which well-known port does HTTPS use? börja lära sig
|
|
|
|
|
Which well-known ports does FTP use for control and data? börja lära sig
|
|
21 (control) and 20 (data)
|
|
|
Which well-known port does SMTP Submission (authenticated mail submission) use? börja lära sig
|
|
|
|
|
Which well-known port does POP3 (unencrypted) use? börja lära sig
|
|
|
|
|
Which well-known port does IMAP (unencrypted) use? börja lära sig
|
|
|
|
|
Which well-known port and protocol does DNS primarily use for queries? börja lära sig
|
|
|
|
|
Which well-known port does NTP (Network Time Protocol) use? börja lära sig
|
|
|
|
|
Which well-known port does SNMP Trap use to receive notifications? börja lära sig
|
|
|
|
|
Which well-known port does LDAP use? börja lära sig
|
|
|
|
|
Which well-known port does SMB (Windows file sharing) use? börja lära sig
|
|
|
|
|
Which registered port does PostgreSQL use? börja lära sig
|
|
|
|
|
DNS uses TCP instead of UDP in which situation(s)? börja lära sig
|
|
Zone transfers and responses larger than
|
|
|
What is the minimum size of a TCP header? börja lära sig
|
|
|
|
|
Which IP protocol number is assigned to TCP? börja lära sig
|
|
|
|
|
Why does TCP use a 3-Way Handshake instead of a 2-Way Handshake? börja lära sig
|
|
Both sides need to synchronise independent Initial Sequence Numbers and confirm bidirectional reachability
|
|
|
Why is the Initial Sequence Number (ISN) chosen pseudo-randomly? börja lära sig
|
|
To prevent TCP sequence prediction attacks (RFC 6528)
|
|
|
How long does the TIME_WAIT state typically last? börja lära sig
|
|
|
|
|
Which TCP flag is used to abruptly terminate a connection (no graceful teardown)? börja lära sig
|
|
|
|
|
How does TCP detect packet loss using duplicate ACKs (Fast Retransmit)? börja lära sig
|
|
After receiving 3 duplicate ACKs (4 ACKs with the same number), retransmit the missing segment immediately
|
|
|
A TCP connection in ESTABLISHED state means: börja lära sig
|
|
The 3-Way Handshake is complete and data can flow in both directions
|
|
|
Many connections in SYN_RECEIVED state on a server most likely indicate: börja lära sig
|
|
A potential SYN flood attack
|
|
|
What is the size of the UDP header? börja lära sig
|
|
|
|
|
How many fields does the UDP header contain? börja lära sig
|
|
4 (source port, destination port, length, checksum)
|
|
|
Which of the following is NOT a typical reason to choose UDP over TCP? börja lära sig
|
|
Guaranteed in-order delivery
|
|
|
Which statement about TCP and broadcast/multicast is correct? börja lära sig
|
|
TCP cannot perform broadcast or multicast — it is strictly point-to-point
|
|
|
What does Flow Control protect against, and what mechanism is used? börja lära sig
|
|
Protects the receiver from buffer overflow; uses the Receiver Window (rwnd)
|
|
|
During TCP Slow Start, how does the congestion window (cwnd) grow? börja lära sig
|
|
Exponentially — it doubles every RTT (starting from 1 MSS)
|
|
|
When TCP detects loss via RTO timeout (no ACKs at all), how does it react? börja lära sig
|
|
Resets cwnd to 1 MSS and restarts Slow Start
|
|
|
ECN (Explicit Congestion Notification) allows congestion to be signalled: börja lära sig
|
|
By routers marking IP packets instead of dropping them
|
|
|
Which transport protocol does HTTP/3 use? börja lära sig
|
|
|
|
|
A "connection refused" error when connecting to a TCP service usually means: börja lära sig
|
|
No process is listening on the requested port (the server sent RST)
|
|
|
Which sysctl tweak helps when a server runs out of ephemeral source ports? börja lära sig
|
|
Extending the ephemeral port range via net. ipv4. ip_local_port_range
|
|
|
Which HTTP status code is returned when a new resource has been successfully created, for example after a successful POST? börja lära sig
|
|
|
|
|
What is the key difference between a 307 Temporary Redirect and a classic 302 Found? börja lära sig
|
|
307 guarantees the HTTP method (e.g. POST) is preserved on the redirected request, whereas
|
|
|
Which status code tells the client that the resource was deliberately and permanently removed, and will not return (stronger than 404)? börja lära sig
|
|
|
|
|
A server is temporarily overloaded or down for maintenance and cannot handle the request right now. Which status code is correct? börja lära sig
|
|
|
|
|
A response includes the header "ETag: "v17-cd23"". On a later request, which header does the client send to ask the server whether the cached copy is still valid? börja lära sig
|
|
|
|
|
What does "Transfer-Encoding: chunked" allow a server to do? börja lära sig
|
|
Send the response body in pieces without knowing the total length in advance, omitting Content-Length
|
|
|
What is the primary purpose of the HTTP OPTIONS method? börja lära sig
|
|
To discover the communication options (e.g. allowed methods) available for a resource, also used in CORS preflight
|
|
|
During TLS negotiation, which extension lets the client and server agree on the application protocol (e.g. h2 for HTTP/2) within the handshake? börja lära sig
|
|
ALPN (Application-Layer Protocol Negotiation)
|
|
|
An SRV record encodes which information for locating a service? börja lära sig
|
|
Priority, weight, port and target hostname for a named service
|
|
|
What is "negative caching" in DNS? börja lära sig
|
|
Caching the fact that a name does NOT exist (an NXDOMAIN response) for a period defined by the SOA, to avoid repeated failing lookups
|
|
|
Which of the following is NOT a Layer 7 protocol? börja lära sig
|
|
|
|
|
When you type "amazon. de" and press Enter, which step happens FIRST? börja lära sig
|
|
DNS resolves the name to an IP address
|
|
|
HTTP is fundamentally based on which communication pattern? börja lära sig
|
|
|
|
|
In an HTTP request, which line comes first? börja lära sig
|
|
The request line (method + path + version)
|
|
|
Which HTTP header tells the server which website the request is for, when multiple sites share one IP? börja lära sig
|
|
|
|
|
Which HTTP method is used to READ a resource without modifying it? börja lära sig
|
|
|
|
|
Which HTTP method is NEITHER safe NOR idempotent? börja lära sig
|
|
|
|
|
An HTTP status code starting with 2xx indicates: börja lära sig
|
|
|
|
|
An HTTP status code starting with 4xx indicates: börja lära sig
|
|
The client made a mistake
|
|
|
Which status code means "the resource has not been modified, use your cached copy"? börja lära sig
|
|
|
|
|
What is the precise meaning of HTTP status code 403? börja lära sig
|
|
Authenticated, but you are not authorised to access this resource
|
|
|
Which status code is typically returned by a reverse proxy when it cannot reach the backend? börja lära sig
|
|
|
|
|
What is the main performance limitation of HTTP/1.1 that browsers worked around by opening 6 to 8 parallel TCP connections? börja lära sig
|
|
Only one request can be in flight per TCP connection at a time
|
|
|
Which feature of QUIC lets an HTTP/3 session survive a Wi-Fi to cellular network switch? börja lära sig
|
|
Connection migration (via connection IDs instead of the 4-tuple)
|
|
|
HTTPS is best described as: börja lära sig
|
|
HTTP wrapped in a TLS encryption layer
|
|
|
What is the primary purpose of HTTP cookies? börja lära sig
|
|
To give HTTP state — for example, to remember that a user is logged in
|
|
|
Which architectural model does nginx primarily use, that makes it efficient for handling many idle connections? börja lära sig
|
|
Event-driven with a small number of worker processes
|
|
|
Which API style is the default choice for public APIs and uses JSON over HTTP? börja lära sig
|
|
|
|
|
What is the primary function of DNS? börja lära sig
|
|
Translate human-readable domain names into IP addresses (and vice versa)
|
|
|
Which symbol represents the DNS root zone? börja lära sig
|
|
|
|
|
When your browser needs to resolve a domain name, which server does it talk to directly? börja lära sig
|
|
Its configured resolver (often the ISP or a public resolver like 1.1.1.1)
|
|
|
Which DNS record type maps a name to an IPv4 address? börja lära sig
|
|
|
|
|
Which DNS record type defines an alias from one name to another name? börja lära sig
|
|
|
|
|
Which DNS record type lists the authoritative nameservers for a domain? börja lära sig
|
|
|
|
|
Which DNS record type controls which Certificate Authorities are allowed to issue TLS certificates for a domain? börja lära sig
|
|
|
|
|
What does DNSSEC protect against? börja lära sig
|
|
Tampering and cache poisoning of DNS answers (integrity)
|
|
|
What is one practical advantage of DoH over DoT? börja lära sig
|
|
DoH traffic looks identical to normal HTTPS, making it much harder to block or distinguish on the network
|
|
|
What is the primary defence against DNS cache poisoning attacks? börja lära sig
|
|
DNSSEC, combined with randomised source ports and transaction IDs
|
|
|
A standard MTA from 1985 receives a modern MIME message with base64 attachments it cannot interpret. What does it do? börja lära sig
|
|
It relays the message unchanged, because MIME lives entirely inside the body and is invisible to SMTP
|
|
|
Why is the LMTP / local pipe used by the MDA (typically port 24) distinct from SMTP relay on port 25? börja lära sig
|
|
LMTP delivers to the final mailbox store and returns a separate status per recipient instead of queuing
|
|
|
Which SMTP reply code is returned by QUIT when the server closes the session politely? börja lära sig
|
|
|
|
|
What is the difference between reply codes 450 and 550 for an unavailable mailbox? börja lära sig
|
|
450 is a transient failure (retry later);
|
|
|
The SMTP VRFY command is usually disabled on public servers. Why? börja lära sig
|
|
It lets an attacker confirm which addresses exist, leaking valid recipients for spam or attacks
|
|
|
What is the advantage of BDAT (CHUNKING, RFC 3030) over the classic DATA command? börja lära sig
|
|
BDAT sends a declared byte count so no dot-stuffing or end-of-data scanning is needed
|
|
|
A receiving MTA does not advertise SMTPUTF8 but a sender tries to use an internationalised (UTF-8) address. What is the correct rejection? börja lära sig
|
|
550 5.6.7 Need SMTPUTF8 support
|
|
|
A DSN message is structured using which MIME content type defined by RFC 3464? börja lära sig
|
|
|
|
|
What is the primary purpose of the Message-ID: header? börja lära sig
|
|
A globally unique, domain-scoped identifier used for threading (In-Reply-To/References) and loop/duplicate detection
|
|
|
Which MIME multipart subtype glues independent parts such as a text body plus separate file attachments? börja lära sig
|
|
|
|
|
Quoted-printable encoding represents the byte 0xE2 (part of a UTF-8 sequence) on the wire as börja lära sig
|
|
|
|
|
The internationalised domain münchen. de is stored on the wire (without SMTPUTF8) as which Punycode form? börja lära sig
|
|
|
|
|
In a DKIM-Signature header, what does the bh= tag contain? börja lära sig
|
|
The hash of the canonicalised message body
|
|
|
In a DKIM-Signature, "c=relaxed/relaxed" specifies börja lära sig
|
|
the canonicalisation algorithms applied to the header and body before hashing
|
|
|
In a DMARC record, what does the pct= tag control? börja lära sig
|
|
The percentage of mail to which the published policy is applied (useful during rollout)
|
|
|
What problem does ARC (Authenticated Received Chain, RFC 8617) solve? börja lära sig
|
|
It preserves original SPF/DKIM/DMARC results across forwarders so legitimate forwarded mail is not failed
|
|
|
Which acronym describes the email client a user actually interacts with (Outlook, Thunderbird, Apple Mail)? börja lära sig
|
|
|
|
|
Which agent relays mail between domains using DNS MX lookups? börja lära sig
|
|
MTA — Mail Transfer Agent
|
|
|
What does it mean that email is "store-and-forward"? börja lära sig
|
|
Each MTA accepts the whole message into a queue and only then attempts the next hop
|
|
|
Which addresses constitute the SMTP "envelope" of an email? börja lära sig
|
|
|
|
|
Which Content-Transfer-Encoding is best suited for arbitrary binary attachments like PDFs and images? börja lära sig
|
|
|
|
|
Which SMTP port is reserved for MTA-to-MTA relay between domains? börja lära sig
|
|
|
|
|
Which SMTP port provides implicit TLS (encrypted from byte 1) for client submission, re-blessed by RFC 8314? börja lära sig
|
|
|
|
|
SMTP is best characterised as which kind of protocol? börja lära sig
|
|
Stateful, plain-text, line-oriented, command/response over a single TCP connection
|
|
|
An SMTP reply code starting with 5xx means: börja lära sig
|
|
Permanent negative — stop, do not retry
|
|
|
Which SMTP command requests the extended capability list (ESMTP)? börja lära sig
|
|
|
|
|
How does the DATA portion of an SMTP message end? börja lära sig
|
|
A line containing only a single dot (CRLF. CRLF)
|
|
|
Which SMTP AUTH mechanism is considered modern and resistant to replay attacks? börja lära sig
|
|
|
|
|
When picking among multiple MX records for a domain, which one does the sender try first? börja lära sig
|
|
The MX record with the lowest preference number
|
|
|
Which port is used for POP3 with implicit TLS (POP3S)? börja lära sig
|
|
|
|
|
Why is POP3 mostly considered legacy in 2026? börja lära sig
|
|
It cannot natively synchronise folders, flags or read-state across multiple devices
|
|
|
Which port is used for IMAP with implicit TLS (IMAPS)? börja lära sig
|
|
|
|
|
What is the difference between FETCH BODY[TEXT] and FETCH BODY. PEEK[TEXT]? börja lära sig
|
|
BODY[TEXT] implicitly sets the Seen flag; BODY. PEEK[TEXT] retrieves the content without changing any flag
|
|
|
How does a STRIPTLS downgrade attack work against mail submission? börja lära sig
|
|
An on-path attacker silently removes the STARTTLS line from the server's EHLO reply, causing the client to fall back to plaintext
|
|
|
What does SPF (RFC 7208) publish? börja lära sig
|
|
A list of IP addresses authorised to send mail for a domain (as a DNS TXT record)
|
|
|
Which DMARC policy value tells receivers to monitor only and apply no enforcement? börja lära sig
|
|
|
|
|
Which mechanism preserves SPF, DKIM and DMARC results across mailing-list forwarders that would otherwise break them? börja lära sig
|
|
[moodle]ARC — Authenticated Received Chain (RFC 8617)
|
|
|
How many layers does the OSI reference model define? börja lära sig
|
|
|
|
|
Which OSI layer is closest to the end user? börja lära sig
|
|
|
|
|
What is the Protocol Data Unit (PDU) at the OSI Transport layer? börja lära sig
|
|
|
|
|
What is the Protocol Data Unit (PDU) at the OSI Data Link layer? börja lära sig
|
|
|
|
|
Which is the correct order of the OSI layers from Layer 1 to Layer 7? börja lära sig
|
|
Physical, Data Link, Network, Transport, Session, Presentation, Application
|
|
|
Which OSI layer provides end-to-end data delivery, reliability, and flow control? börja lära sig
|
|
Transport layer (Layer 4)
|
|
|
Which OSI layer transmits raw bits over a physical medium? börja lära sig
|
|
|
|
|
Which OSI layer handles data format translation, encryption, and compression? börja lära sig
|
|
Presentation layer (Layer 6)
|
|
|
Character encoding such as ASCII and Unicode is a task of which OSI layer? börja lära sig
|
|
Presentation layer (Layer 6)
|
|
|
Data compression to reduce the size of transmitted data is performed at which OSI layer? börja lära sig
|
|
Presentation layer (Layer 6)
|
|
|
Dialog control and the management of full-duplex, half-duplex, and simplex communication modes is a function of which OSI layer? börja lära sig
|
|
|
|
|
Which of the following are listed as examples of Session layer mechanisms? börja lära sig
|
|
NetBIOS, RPC, and login sessions
|
|
|
Which of the following is an Application layer protocol used for name resolution? börja lära sig
|
|
|
|
|
SMTP, POP3, and IMAP are Application layer protocols used for which service? börja lära sig
|
|
|
|
|
Which Transport layer protocol is connection-oriented and provides reliable delivery? börja lära sig
|
|
|
|
|
Which characteristic best describes UDP compared to TCP? börja lära sig
|
|
Low overhead and fast, with no guaranteed delivery
|
|
|
What identifies the application associated with a Transport layer communication? börja lära sig
|
|
|
|
|
At the Network layer, what kind of address identifies a device across networks? börja lära sig
|
|
IP address (logical address)
|
|
|
Which protocols operate at the OSI Network layer? börja lära sig
|
|
|
|
|
Packet fragmentation, when needed, is handled by which OSI layer? börja lära sig
|
|
|
|
|
How does the Data Link layer detect errors in received frames? börja lära sig
|
|
Using a Cyclic Redundancy Check (CRC)
|
|
|
Which protocols are associated with the Data Link layer? börja lära sig
|
|
Ethernet (802.3) and Wi-Fi (802.11)
|
|
|
Which of the following does the Physical layer define? börja lära sig
|
|
Electrical, optical, or radio signals, voltage levels, and signal timing
|
|
|
In the OSI model, the upper layers (5, 6, and 7) are often grouped as which category? börja lära sig
|
|
|
|
|
How many layers does the TCP/IP model commonly have? börja lära sig
|
|
4 (sometimes described as 5)
|
|
|
The TCP/IP Internet layer corresponds to which OSI layer? börja lära sig
|
|
|
|
|
The TCP/IP Transport layer corresponds to which OSI layer? börja lära sig
|
|
Transport layer (Layer 4)
|
|
|
Which protocols are listed for the TCP/IP Internet layer? börja lära sig
|
|
|
|
|
Which organization is credited with developing the TCP/IP model? börja lära sig
|
|
|
|
|
In practice, why do engineers still use OSI layer numbers (such as "Layer 3 switch")? börja lära sig
|
|
OSI numbers are used to describe concepts, while TCP/IP protocols are used for actual communication
|
|
|
During encapsulation, in what order is the data transformed from the Application layer down to the Physical layer? börja lära sig
|
|
Data, Segment, Packet, Frame, Bits
|
|
|
What part of a PDU carries the actual user information rather than control information? börja lära sig
|
|
|
|
|
According to the slides, what does PDU stand for? börja lära sig
|
|
|
|
|
What does PCI (Protocol Control Information) refer to in a layered model? börja lära sig
|
|
The header and/or trailer added by each layer
|
|
|
What is a Service Access Point (SAP)? börja lära sig
|
|
The interface between adjacent layers
|
|
|
Which device operates at the Physical layer and simply regenerates or repeats signals to all ports? börja lära sig
|
|
|
|
|
A router makes forwarding decisions based on which type of address? börja lära sig
|
|
|
|
|
A firewall that filters traffic based on IP addresses and TCP/UDP port numbers operates at which OSI layers? börja lära sig
|
|
Network and Transport layers (Layers 3 and 4)
|
|
|
Which organization manages Internet standards published as RFCs? börja lära sig
|
|
IETF (Internet Engineering Task Force)
|
|
|
Which standards organization is part of the United Nations and focuses on telecommunication standards? börja lära sig
|
|
ITU (International Telecommunication Union)
|
|
|
Which RFC defines TCP (Transmission Control Protocol)? börja lära sig
|
|
|
|
|
Which RFC number corresponds to the very first RFC, "Host Software"? börja lära sig
|
|
|
|
|
What is the definition of a protocol given in the slides? börja lära sig
|
|
The rules for the format, order, and actions of messages exchanged between communicating entities
|
|
|
What is the main reason for using a layered architecture in networking? börja lära sig
|
|
Complexity management — breaking a huge problem into smaller, manageable parts
|
|
|
Which benefit of layering means each layer only needs to know the interface of adjacent layers? börja lära sig
|
|
|
|
|
A LAN speed is given as "1-10 Gbps" in the slides. What does Gbps measure? börja lära sig
|
|
Data rate (gigabits per second)
|
|
|
Bit rate, voltage levels, and signal timing are defined at which OSI layer? börja lära sig
|
|
|
|
|
The Data Link layer adds both a header and a trailer to data from Layer 3. What is the trailer field used for error detection commonly called? börja lära sig
|
|
Frame Check Sequence (FCS)
|
|
|
During encapsulation, which layer adds the header that turns "Data" into a "Segment"? börja lära sig
|
|
The Transport layer (Layer 4)
|
|
|
A device described as operating at "Layer 3" forwards data based on which information? börja lära sig
|
|
|
|
|
When two hosts negotiate, maintain, and gracefully end a logical conversation independent of the underlying transport connection, which OSI layer is conceptually responsible? börja lära sig
|
|
|
|
|
In the TCP/IP model, the Session, Presentation, and Application layers of OSI are combined into a single Application layer. börja lära sig
|
|
|
|
|
